Fabricatores et Provisores Tabularum Compositarum Aluminii in Sinis ab Anno MMII - Henglicai ACP
Lingua
Fabricatores et Provisores Tabularum Compositarum Aluminii in Sinis ab Anno MMII - Henglicai ACP
Constructione technology fecit tentorium ex siccoaluminium plastic laminam
Et processerunt ut irent ①
Setting out shall be carried out according to the actual center line and elevation point of civil engineering; Ex axis ad aedificationem
Aluminium plastic laminam compage hoc composito ex coordinatione, et subordinatione membra. Primo situ linea verticali franguntur membra membris verticale punctum determinare ancora.
Install fixa ② iungo
Profectus ex fige iungo cum glutino ultrices adpone binae tunicae in pugillo antirust pingunt. Iungo cum haereret in partes redacti fixa consectetur consequat. When there are no embedded iron parts on the main structure, holes can be drilled on the main structure and expansion bolts can be installed to fix the connector.
③ Install frame
Vicifontem constitutus fuerit ab intra et mediam aciem dignitasque viguit aliquando cohibeatur. Simul cruces articulo coniuncta Welds erit tractari antirust pingunt et abscondi inspectionem monumenta erunt pro certo connexiones etiam longitudo latitudinem positura integer elevationem quantitate immersa profundo iungo Welds .
④ instruitur de aluminium plastic laminam
On the inner frame of the profile, the screw holes shall be milled first, and the aluminum-plastic plate finish shall be fixed on the profile steel frame one by one with rivets; Gap inter de ~ 15mm X cm est, et inject silicone sealant tempestas resistentia; Before the installation of aluminum plate, it is forbidden to remove the packaging paper until the packaging protective film is torn off before the completion;
Rationis plasticae ex eâ aluminium laminam sagittis.
Aluminium laminam dignissim elit constructione habebat murum
Aluminium plastic laminam murum installation columnae ejus ad 1.2.1 sagum obviam sequenti requisita:
(1) The column shall be connected with the connector first, and then the connector shall be connected with the embedded parts of the main body, and shall be adjusted and fixed. Columnae institutionem marcam
The height deviation shall not be greater than 3mm, the front and rear deviation of the axis shall not be greater than 2mm, and the left and right deviation shall not be greater than 3mm.
(2) The installation elevation deviation of two adjacent columns shall not be greater than 3mm, and the maximum elevation deviation of columns on the same floor shall not be greater than 5mm
Non longe maior deuiatio 2mm.
1.2.2 aluminium plastic laminam institutionem sagum trabem muri ejus obviam sequenti requisita:
(1) The connectors and gaskets at both ends of the beam shall be installed at the predetermined position of the column, which shall be installed firmly, and the joints shall be tight;
(II) in horizontalem elevation excessus duorum adjacent atra texit erroris non esse maiorem quam 1mm. Elevation deviation of the same floor: when the width of a wall is less than or equal to 35m, it is not allowed
5mm major erit; Et habebat murum maior 35m latum, nec maior 7mm.
Aluminium plastic laminam murum institutionem 1.2.3 sagum in occursum components et haec necessario
(I) In coordinatione, et subordinatione inspecta sit et sodales connectens, metiri et adaequatum;
(2) When installing components, the deviation between left and right, up and down shall not be greater than 1.5mm;
(III) Per installation of articulis inanis, ibi necesse est quod sit supra foramina IMPERVIUS secundum consilium requisita,
(4) When filling silicone weather resistant adhesive, the width and thickness of aluminum-plastic plate joint shall be constructed according to the technical parameters calculated in the design.
1.2.4 the allowable assembly deviation of vertical and transverse members of aluminum plastic plate curtain wall shall comply with the provisions in the following table.
Item ratio magnitudinis erucae liceret discedere inspicienda
1. Utere tape chalybe ut metiaris distantiam inter duo membra verticalia adjacentia (finis fixum) ± 2.0
Regula regens per duas laminas aluminii adjacentes infra 20m± 1.5± 2.0
2. Ferri machina adhibenda est cum distantia duorum membrorum transversalium adjacentium minor est quam 2000 et temporis spatium ≥ 2000 ± 1.5 ± 2.0
3. Diagonalis differentia divisionis 3. Quando diagonalis longitudo minor est quam 2000 et diagonalis ≥ 2000 est, 3.03.5 cum taenia ferro vel extensione rectoris.
4. Cum verticalitas membrorum verticalium altitudo sit ≤ 30m, quando altitudo ≤ 60m est, quando altitudo 90m ≤ est ≤, cum altitudo sit> 90m, utere instrumento theodolite vel laser
Differentia est 2 vel 2 gradus inter duas laminas ferro adjacentes
6. Gradus membri transversi cum membrum longitudo minor est quam 2000 et membrum longitudo est ≥ 2000 23 gradu vel gradu
7. 2.0m regula dirigens adhibebitur ad rectitudinem membrorum verticalium
8. Planities superficiei exterioris membri verticalis erit ≤ 2 ≤ 5 ≤ 7 ≤ 9 cum latitudo trium columnarum adiacentium est ≤ 20m, latitudo ≤ 40m, latitudo ≤ 60m, latitudo> 60m
≤ 10 instrumentum laser
9 planities longitudo membri transversi principalis in eadem altitudine ≤ 35m longitudinis ＞ 35m ≤ 5 ≤ 7 uti libella
10. Horizontalis angulus inclusus bracteae connectentis sub aluminio laminae plasticae permittitur sursum benificium, non deorsum + 2.0-0 tangentis METIOR.
11. In laminae aluminii connectentis angulus horizontalis inclusus inclusus per + 0-2.0 deorsum petere licet.
