دانش صفحه پلاستیکی آلومینیوم -ویژگی های صفحه پلاستیکی آلومینیوم و فرآیند تولید

2022/04/28

hlcaluminium -پانل های کامپوزیت آلومینیوم تولید کنندگان

دانش تخته آلومینیوم -پلاستیک -ویژگی های صفحه آلومینیوم -پلاستیک و فرآیند تولید I. ویژگی های تابلوهای آلومینیومی: آلومینیوم:

صفحه آلومینیوم -پلاستیک نوع جدیدی از مواد تزئینی است. در مقایسه با سایر مواد تزئینی ، برتری بی نظیر بسیاری دارد. از یک طرف ، تخته های پلاستیکی آلومینیومی یک ماده کامپوزیت هستند که می توانند خواص جدیدی را بدست آورند که بسیاری از اجزای اصلی از طریق کامپوزیت به دست می آیند.

از طرف دیگر ، تخته های آلومینیوم -پلاستیک محصولی با فناوری بالا هستند. خواه تولید باشد یا کاربردی ، حاوی محتوای فنی بالایی است.

بسیاری از فرآیندهای پیشرفته در تولید استفاده می شود ، مانند فناوری روکش روتختی و فناوری کامپوزیت حرارتی مداوم ، از بازی کامل عملکرد مواد.

ویژگی های اصلی تابلوهای پلاستیکی آلومینیومی در جنبه های زیر آشکار می شود.

1. کیفیت کوچک:

صفحات آلومینیوم پلاستیک از مواد هسته پلاستیکی با آلومینیوم و چگالی کمتری تشکیل شده است ، بنابراین با آلومینیوم (یا سایر فلزات) با همان استحکام یا ضخامت در مقایسه با کیفیت آنها در مقایسه با آلومینیوم (یا سایر فلزات) در مقایسه با آلومینیوم (یا سایر فلزات) ، کیفیت آنها از شیشه و سنگ کوچک است. کیفیت حتی با کیفیت تر است. بسیار کوچکتر است

2. استحکام خوب:

تخته آلومینیوم -پلاستیک هوشمندانه از اصل مکانیکی ساختار فولادی فولاد استفاده می کند و گرسنگی هوشمندانه به آن خواص مکانیکی منحصر به فردی می بخشد. علاوه بر این ، تابلوهای پلاستیکی آلومینیومی در شرایط دمای بالا به ترکیب می رسند و صفحه آلومینیومی دو لایه از صفحات آلومینیومی در کل فرآیند پردازش در حالت تنش مشخص است ، هنگامی که نوع کولر خنک می شود ، زیرا آلومینیوم متقارن صفحه و مواد اصلی در میزان انقباض تولید می شوند ، استرس داخلی تخته پایدار است و از استحکام خوبی برخوردار است. در مقایسه با صفحات آلومینیومی تک لایه ، حد کشش آن زیاد است ، تولید تغییر شکل آسان نیست. در یک حالت طبیعی و بدون نیروی خارجی ، می تواند عملکرد مسطح خوبی را برای مدت طولانی حفظ کند.

3. رنگ غنی و تزئینی قوی:

سطح صفحه پلاستیکی آلومینیوم را می توان در رنگ های مختلفی برای انجام طراحی الگوی که مطابق با همه کاربردها است ، انجام داد.

علاوه بر این ، به منظور استفاده از الگوهای شبیه سازی فناوری کپی عکاسی ، گرانیت ، دانه چوب و الگوهای فلزی ، یک طرح الگوی با یک تک رنگ ، بافت دقیق و طراحی الگوی با کیفیت بالا را ارائه می دهد. طراحی رنگ و الگوی غنی با هماهنگی که مطابق با الزامات محیط مختلف است ، مطابقت دارد و این امکان را فراهم می کند که سبک های مختلف معماری با محیط سازگار باشد ، رنگ و محیط انتخاب شده هماهنگ است و اثر کلی هنری کامل است. لذت بصری دیوار پرده ای که با پانل های پلاستیکی آلومینیومی تزئین شده است ، نسبت به دیوار پرده شیشه ای زرق و برق دار و دیوار پرده سنگی زیبا پایین نیست.

در زیر خورشید ، سطح آن زرق و برق دار و با عزت است و در عین حال از آلودگی نور جلوگیری می کند.

4. صافی سطح بالا:

تابلوهای آلومینیومی با فرآیندهای تولید مداوم گرم و ترکیبی تولید می شوند. بنابراین ، در مقایسه با یک صفحه فلزی واحد ، صاف بودن سطح آن زیاد است ، به خصوص صفحات با اندازه بزرگ آشکارتر است. برای دکوراسیون ساختمان ، ظاهری مسطح و مسطح دارد.

5. دوام خوب:

صفحه آلومینیوم پلاستیک از فناوری کامپوزیت حرارتی فلزی و هسته استفاده می کند ، که کاملاً پیوند خورده است. پوشش های سطح با توجه به محیط استفاده متفاوت از مواد مختلف انتخاب می شوند. به طور کلی ، از سه نوع پوشش استفاده می شود ، یعنی پوشش های فلوئوروکربن ، پوشش های پلی استر و روکش های آکریلیک. پوشش های کربن از مقاومت در برابر آب و هوا بهتر برخوردار هستند و بیشتر در دکوراسیون دیواره پرده و موارد خاص مورد استفاده قرار می گیرند. مطالعات آزمایش نشان داده است که می توان بیش از 20 سال در محیط های سخت در فضای باز استفاده کرد.

6. پردازش خوب:

Aluminum -plastic plates are composed of aluminum and plastic. It is easy to process cutting, punching, digging, and bending. It can be processed with aluminum or woody processing equipment. Therefore, not only can be processed in the production plant, the proposed composite board can be processed on -site.

7. Excellent fire resistance:

In the aluminum -plastic board series, the fire -resistant aluminum plastic board uses a newly developed core material. This core material is filled in the filling feather. نیاز.

8. Good cost characteristics:

The production of aluminum -plastic boards adopts the continuous heat composite process of pre -coating and the metal/core material. Compared with the general metal veneer, the production efficiency is high and the cost of raw materials is low. It is a material with good cost characteristics.

9. Good environmental coordination:

The aluminum and plastic core in the abandoned aluminum -plastic plate can be used 100%for regeneration, and the environmental load is low.

In addition, the wood -aluminum plastic plate and outdoor decorative aluminum plastic plate uses fluorocarbon coatings. The products have high durability and low daily maintenance costs, reducing the cost of the entire life cycle.

10. Wide use:

Aluminum -plastic panels are cost -effective and widely used. In addition to the decoration of curtain walls, inner and outer walls, hall halls, restaurants, shops, conference rooms, etc., it can also be used for the reconstruction of old buildings. Inner and outer walls, etc.

Second, aluminum -plastic board production process:

There are many production processes of aluminum -plastic plates. The composite process of plastic core board and two -sided aluminum plates can be divided into cold compound legal and hot compound legal; it can also be divided into continuous compound legal and intermittent compound legal.

The process of producing aluminum plastic plates is first to clean aluminum coils. Due to the needs of the production of aluminum coils, the surface is coated with lubricants and anti -oxidants, and some dirt will also be attached during transportation, which will affect its adhesion, so it must be cleaned. After the aluminum coil is cleaned and chemically treated, the surface will produce a dense chemical protective film; this layer of chemical film can improve the antioxidant capacity of aluminum coils and extend the life of the paint film.

The general process of cleaning is as follows: aluminum rolls → spraying abandonment → water washing → neutralization → chemical treatment → water washing → drying → cooling → receiving rolls.

The clean aluminum coil was sent to the coating machine and coated high -performance fluorocarbon resin on the surface of the aluminum coil. The process process is as follows:

Aluminum rolls → feeding → coating fluorocarbon coatings → hot air circulating paint → cooling → covering → cutting → collection.

The panel of the outer wall aluminum plastic plate should be coated with two layers of paint and primer. The surface paint of the outer wall plate is a fluorocarbon resin coating with extremely high weather resistance, that is, polyfront diofluoroethylene (PVDF). Its excellent anti -ultraviolet performance and anti -environmental pollution can keep the protected aluminum coil surface. Essence The surface of the aluminum -plastic composite board can not only have metal colors, but also beautiful marble patterns and colors.

Fluorocarbon coatings usually apply roller coating methods to aluminum coils, and then baked at high temperature to dry it. The equipment is continuous production, first paint paint, then paint paint, and finally coat the coatings. The total thickness of the three layers of paint is 30 μm. Each lacquer needs to be baked for about 60s above 200 ° C to dry it. After the oven is released, it quickly cools through the air -cooled machine.

The inner wall paint can use epoxy resin, polyester resin and acrylic resin. After the paint, top paint, and surface paint are painted, a layer of PE protective film is pasted on the coating layer surface to avoid being scratched during the processing and transportation and installation of the surface coating.

The protective film is self -mucous membrane, and it can be unveiled after installation.

کویل های آلومینیومی با رزین فلوئوروکربن می توانند با مواد هسته پلاستیکی فرآیند ترکیب شوند. هسته پلاستیکی در اصل سه لایه است ، وسط آن پلاستیک PE است و دو طرف چسب هستند. ورق ها و چسب های PE را می توان به طور جداگانه تولید کرد ، و همچنین می تواند در سه لایه از معمولاً فشرده شود.

ورق سه لایه تولید شده از Archaea/PE/چسب با لایه های فوقانی و تحتانی صفحه آلومینیومی پیچیده شده است. صفحه کامپوزیت آلومینیومی کامپوزیت آلومینیوم پلاستیک در هر دو طرف صفحه آلومینیومی با ضخامت 0.15 میلی متر است و لایه هسته 3 تا 3 ~ 5 میلی متر است ، ضخامت کل 4-6 میلی متر است. سرانجام به مشخصات 1220mm × 2440mm برش دهید.

ذات

با ما تماس بگیرید
فقط به ما نیازهای خود را بگویید، ما می توانیم بیشتر از آنچه شما می توانید تصور کنید.
درخواست خود را ارسال کنید
Chat with Us

درخواست خود را ارسال کنید

زبان دیگری انتخاب کنید
English
العربية
Deutsch
Español
français
italiano
日本語
한국어
Português
русский
简体中文
繁體中文
Afrikaans
አማርኛ
Azərbaycan
Беларуская
български
বাংলা
Bosanski
Català
Sugbuanon
Corsu
čeština
Cymraeg
dansk
Ελληνικά
Esperanto
Eesti
Euskara
فارسی
Suomi
Frysk
Gaeilgenah
Gàidhlig
Galego
ગુજરાતી
Hausa
Ōlelo Hawaiʻi
हिन्दी
Hmong
Hrvatski
Kreyòl ayisyen
Magyar
հայերեն
bahasa Indonesia
Igbo
Íslenska
עִברִית
Basa Jawa
ქართველი
Қазақ Тілі
ខ្មែរ
ಕನ್ನಡ
Kurdî (Kurmancî)
Кыргызча
Latin
Lëtzebuergesch
ລາວ
lietuvių
latviešu valoda‎
Malagasy
Maori
Македонски
മലയാളം
Монгол
मराठी
Bahasa Melayu
Maltese
ဗမာ
नेपाली
Nederlands
norsk
Chicheŵa
ਪੰਜਾਬੀ
Polski
پښتو
Română
سنڌي
සිංහල
Slovenčina
Slovenščina
Faasamoa
Shona
Af Soomaali
Shqip
Српски
Sesotho
Sundanese
svenska
Kiswahili
தமிழ்
తెలుగు
Точики
ภาษาไทย
Pilipino
Türkçe
Українська
اردو
O'zbek
Tiếng Việt
Xhosa
יידיש
èdè Yorùbá
Zulu
زبان فعلی:فارسی